Protech ZOOM 425 ccpm Spécifications Page 133
- Page / 240
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
14.4. Always disconnect the battery when working on the
helicopter
Warning
ALWAYS DISCONNECT THE BATTERY WHEN POSSIBLE IF WORKING ON
THE HELICOPTER. IF YOU MUST WORK ON A LIVE HELI, THEN DISCON-
NECT AT LEAST ONE OF THE MOTOR LEADS SO THE MAIN ROTOR/TAIL
ROTOR WILL NOT SPIN UP AND MAIM YOU.
If the main rotor or tail rotor spins up and maims or kills you, this will probably slow down your
helicopter learning process, so please try to avoid this.
See also:
• www.runryder.com/helicopter/t136510p1
• www.runryder.com/helicopter/t70830p1
• www.runryder.com/helicopter/t98388p1
• www.runryder.com/helicopter/t33625p1
• www.runryder.com/helicopter/t12572p1
14.5. Liability insurance
A membership in your country's local R/C modeling club is highly recommended because it
provides insurance coverage in case you damage something. This is very useful if your heli
damages somebody's car, or injures someone.
In the USA a membership in the Academy of Model Aeronautics (AMA) provides insurance
coverage.
In the UK the British Model Flying Association (BMFA) provides this service.
R/C Heli Rules and Tips
120
- Guide v17 1
- Toshiyasu Morita 2
- Mark Pearson 2
- Table of Contents 4
- List of Tables 12
- 1.2. Repairs are expensive 14
- 2.5. Summary of skills 15
- 3.2. Clones 18
- 3.2.1. Design problems 19
- 3.4.1. Lite Machines Corona 21
- 3.4.4. Ikarus ECO Lite 22
- 3.4.5. Ikarus ECO 8 22
- 3.4.6. Ikarus ECO 16 22
- 3.4.10. JR Voyager E 23
- 3.4.12. Mikado Logo 10 24
- 3.4.13. Mikado Logo 20 24
- 3.4.14. MS Composit Hornet FP 24
- 3.4.15. MS Composit Hornet CP 25
- 3.4.16. MS Composit Hornet II 25
- 3.4.17. Maxir SE 25
- 3.4.19. Quick Quick EP 10 26
- 3.4.20. Quick Quick EP 16 26
- 3.4.22. Align T-Rex 450X 27
- 3.4.24. ARK X-400 27
- 4.1. Beginner configurations 30
- 4.2.2. T-Rex 450XL 32
- 4.2.3. Zoom 400 32
- 4.2.4. Logo 10 - brushless 32
- 4.2.5. ECO 8 - brushed 33
- 4.2.6. ECO 8 - brushless 33
- 5.1. Corona upgrade paths 34
- 5.2. Piccolo upgrade paths 35
- 6.1. Control system 37
- 6.2. Servos 41
- 6.2.2. Tail (rudder) servo 42
- 6.3.1. Batteries 43
- 6.3.2. Battery connectors 45
- General recommendation 47
- 6.3.4. Wire 48
- 6.4. Motors and related items 49
- 6.4.1.2. FP Piccolo motors 50
- 6.4.1.6. Hornet CP motors 51
- 6.4.1.7. Maxir SE motors 51
- 6.4.1.8. Zoom 400 motors 51
- 6.4.1.10. ARK X-400 motors 52
- 6.4.1.11. Voyager E motors 52
- 6.4.1.12. Robbe Eolo motors 52
- 6.4.1.13. ECO 8 motors 52
- 6.4.1.14. ECO 16 motors 54
- 6.4.1.15. Viper 70 motors 54
- 6.4.1.16. Logo 10 motors 54
- 6.4.1.17. Logo 14 motors 55
- 6.4.1.18. Logo 20 motors 55
- 6.4.1.19. Quick EP 10 motors 55
- 6.4.1.21. Summary 56
- 6.4.2. Pinion 57
- 6.4.3. Motor connectors 57
- 6.4.4. Main motor ESC 57
- 6.4.5. Tail motor ESC 60
- 6.5. Other 61
- Helicopter Parts Selection 62
- 7.2. Helicopter tools 64
- 7.2.5. Tachometer 65
- 7.3. Adhesives 66
- 7.4. Charging equipment 67
- 7.4.3. Power supplies 69
- 7.5. Electronic instruments 71
- 7.5.2. Wattmeter 72
- Chapter 8. Simulators 73
- 8.3. Easyfly 75
- 8.4. Aerofly Professional 75
- Simulators 77
- 8.9. ClearView 81
- 8.10. PreFlight 81
- 8.11. PhoenixRC 82
- 8.13. Summary 83
- 8.14. Simulator practice 84
- Chapter 9. Transmitters 85
- 9.3. Transmitter tray 88
- 9.5. Transmitter manuals 89
- 10.1.1. Building 90
- 10.1.2. Threadlock 90
- 10.1.3. Gear lubrication 90
- 10.1.4. Frame assembly 90
- 10.1.5. Stripped threads 90
- 10.1.6. Breaking-in motors 91
- 10.1.7. Carbon dust 91
- 10.1.8. Capacitors 91
- 10.1.9. Motor diode 92
- 10.1.10. Ball links 92
- 10.1.11. Motor shaft 92
- 10.1.13. Canopy painting 93
- 10.1.14. Tail servo 93
- 10.1.15. Mounting component 93
- 10.1.16. Ball in swashplate 93
- Pro) only 95
- Making CA joints 96
- 11.1. Channel assignments 102
- 11.2. Component placement 104
- 11.3. Wire routing 105
- 11.4. Soldering technique 105
- 13.1. Center of gravity setup 109
- 13.2. Swashplate setup 109
- 13.2.2.3. Swashplate leveling 111
- 13.2.3.1. Normal mode setup 111
- 13.2.4.7. Check for binding 114
- 13.2.5.4. Check for binding 114
- 13.4. Main motor setup 117
- 13.5. Tail rotor setup 122
- 13.5.4.1. GY240 setup 123
- 13.5.4.2. GY401 setup 124
- 13.5.4.4. Yaw-rate gyro setup 126
- 13.5.5.1. GY240 setup 127
- 13.5.5.2. Yaw-Rate Gyro setup 128
- 14.5. Liability insurance 133
- 15.1. The skills required 134
- 15.2.3. Use white blades 135
- 17.3. Safety notes 139
- Chapter 18. Tail-In Hovering 140
- 20.1. Introduction 145
- 20.2. Inverted T 145
- 20.3. 90 degree yaw 145
- 20.4. 180 degree yaw 145
- 21.1. Using idle-up mode 147
- 21.3. Banked forward turns 147
- 21.4. Backwards flight 148
- 21.5. Banked backwards turns 148
- 22.1. Figure eights 150
- 23.1. Single pirouette 151
- 24.4. Add flybar weights 153
- 26.1. Vibration problems 155
- 26.2. Tail control problems 157
- 26.3. Throttle/ESC problems 161
- 26.4. Swashplate problems 162
- 26.5. Glitching 162
- 26.6. Other problems 163
- Mikado Logo 10 165
- Ikarus ECO 8/16 165
- Align T-rex 450X/450XL 167
- ARK X-400 167
- Motor vendors 167
- ESC vendors 168
- Servo vendors 168
- BEC manufacturers 169
- Main rotor blades 169
- Carbon fiber tubes and rods 169
- Other suppliers 169
- Hobby associations 170
- Useful webpages and forums 170
- Aerobatics 170
- Magazines 171
- Helicopter theory 171
- 28.1. General questions 172
- 28.2. Transmitters 173
- 28.4. Gyros 177
- 28.5. Helicopter setup 177
- Chapter 29. Helicopter Myths 178
- 30.1. How helicopters work 179
- 30.1.2.1. Throttle stick 180
- 30.1.2.2. Rudder stick 180
- 30.1.3.3. non-CCPM 181
- 30.1.5. The rotorhead 184
- 30.1.7. How gyros work 185
- 30.1.8.1. GY401 setup 188
- 30.1.8.2. GY240 setup 191
- 30.1.10. How ESCs work 192
- 30.1.10.3. Governor mode 193
- 30.1.10.4. Timing Advance 193
- 30.1.11. How batteries work 194
- 30.1.12. How motors work 194
- 30.1.12.1. Brushed motors 195
- 30.1.12.2. Brushless motors 197
- 30.1.12.3. Coreless motors 198
- 30.2. Motor selection guide 199
- 30.2.1.3. Motor efficiency 200
- 30.2.1.4. Motor rated RPM 200
- 30.2.2.1. Motor size 200
- 30.2.2.2. Motor weight 200
- 30.2.2.5. Cooling options 201
- Table 30.5. Heatsinks 201
- 30.2.3. Other characteristics 202
- 30.3. Motor selection table 203
- 30.4. Pinion selection guide 212
- 30.4.3. Shaft sizes 213
- 30.4.4. Pinion notes 213
- 30.5. Pinion selection tables 214
- 30.6. Servo selection guide 217
- 30.6.2.1. Size 218
- 30.6.2.2. Mounting lugs 218
- 30.6.2.3. Servo weight 218
- 30.6.2.4. Speed and Torque 218
- 30.6.2.5. Gear type 218
- 30.8. Battery info 220
- 30.11. Useful equations 225
- Glossary 227
Produits connexes et manuels pour Jouets et accessoires Protech ZOOM 425 ccpm
(20 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.165 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels